Search Results

Air Quality Modeling Working Group developed two models to evaluate effects of automobile emission reduction measures on air quality improvement: Urban Air Quality Simulation Model in which secondary aerosol formation processes have been incorporated, and Roadside Air Quality Simulation Model in which micro-scale traffic flow has been taken into consideration. Concretely, a model has been built up for estimating SPM concentration in ambient air in which high concentrated air pollutants have been contained during summer and winter. The model has been built up by using UAM (Urban Airshed Model) as base model, and the following modification has been made to the base model. First, ISSOROPIA (secondary inorganic aerosol equilibrium model) has been added to the base model, and a secondary organic aerosol formation/reaction model (SOA model) has been incorporated into the model.

To achieve high-accuracy measurements of fuel consumption in testing on natural gas vehicles, a method for measuring the absolute value of fuel consumption by the gravimetric method using certificated reference weights and an electric platform scale has been developed. By performing a flow-meter test and a chassis dynamometer test using the gravimetric method, the measurement accuracy of the value of fuel flow rate and fuel consumption obtained by the fuel flow meters, carbon balance method, and air-to-fuel ratio method was evaluated. As a result, a highly accurate method for measuring fuel consumption in chassis dynamometer tests has been confirmed.

The SAE Fuel Cell Vehicle (FCV) Safety Working Group has been addressing FCV safety for over 11 years. In the past couple of years, significant attention has been directed toward a revision to the standard for vehicular hydrogen systems, SAE J2579(1). In addition to streamlining test methodologies for verification of Compressed Hydrogen Storage Systems (CHSSs) as discussed last year,(2) the working group has been considering the effect of vehicle fires, with the major focus on a small or localized fire that could damage the container in the CHSS and allow a burst before the Pressure Relief Device (PRD) can activate and safely vent the compressed hydrogen stored from the container.

A methodology for simulating effect of international variations in fuel compositions on spray combustion is proposed. The methodology is validated with spray combustion experiments with real fuels from three different countries. The compositions of those fuels were analyzed through GC×GC and H-NMR. It was found that ignition delay times, flame region and flame luminosity were significantly affected by the compositional variations. For the simulation, an evaporation surrogate consisting of twenty two species, covering basic molecular types and a wide range of carbon numbers, is developed. Each species in the evaporation surrogate is then virtually converted to a reaction surrogate consisting of n-hexadecane, methylcyclohexane and 1,2,4-trimethyl benzene so that combustion reactions can be calculated with a published kinetic model. The virtual species conversion (VSC) is made so as to take over combustion-related properties of each species of evaporation surrogates.

Diesel Particulate Filter (DPF) is a very effective aftertreatment device to limit particulate emissions from diesel engines. As the amount of soot collected in the DPF increases, the pressure loss increases. Therefore, DPF regeneration needs to be performed. Injected fuel into the exhaust line upstream of the Diesel Oxidation Catalyst (DOC), hydrocarbons are oxidized on the DOC, which increases the exhaust gas temperature at the DPF inlet. It is also necessary that the injected fuel is completely vaporized before entering the DOC, and uniformly mixed with the exhaust gases in order to make the DOC work efficiency. However, ensuring complete evaporation and an optimum mixture distribution in the exhaust line are challenging. Therefore, it is important that the fuel spray feature is grasped to perform DPF regeneration effectively. The purpose of this study is the constructing a simulation model.

The study of 10% ethanol blended gasoline (E10 gasoline) utilization has been conducted in the Japan Auto-Oil Program (JATOP). In order to clarify the impact of E10 gasoline on vehicle performances, exhaust emissions, evaporative emissions, driveability and material compatibility have been investigated by using domestic gasoline vehicles including mini motor vehicles which are particular to Japan. The test results reveal that E10 gasoline has no impact on exhaust emissions, engine startup time and acceleration period under the hot start condition, but a slight deterioration is observed in some test cases under the cold start condition using E10 gasolines with 50% distillation temperature (T50) level set to the upper limit of Japanese Industrial Standards (JIS) K 2202. Regarding evaporative emissions, the tested vehicles shows no remarkable increase in the hot soak loss (HSL), diurnal breathing loss (DBL) and running loss (RL) testing with E10 gasolines.

A new combustion system targeting a drastic decrease in NOx emission and a brake specific energy consumption equivalent to that of a DI diesel engine has been developed. In this new combustion system, a lean burn system using early injection was employed to reduce NOx emission and an auto-ignition DI engine system was employed to achieve the low energy consumption. Methanol was used as the fuel for reducing NOx emission. The objective of this study is to clarify the possibility of the system for the auto-ignition of a premixed lean mixture of methanol fuel. This study shows that the gas temperature at ignition, Tig, is the predominant factor affecting auto-ignition. Auto-ignition occurs when Tig exceeds approximately 1000K. The methanol lean burn system in an auto-ignition DI engine drastically decreased NOx emission with almost the same brake specific energy consumption as a diesel engine in the middle load region.

In the Japan Clean Air Program II (JCAP II) Diesel WG, effects of fuel properties on the performance of two types of diesel NOx emission aftertreatment devices, a Urea-SCR system and a NOx storage reduction (NSR) catalyst system, were examined. For a Urea-SCR system, the NOx emission reduction performance with and without an oxidation catalyst installed in front of the SCR catalyst at low exhaust gas temperature operation was compared. For an NSR catalyst system, the effect of fuel sulfur on both emissions and fuel economy during 50,000 km driving was examined. Furthermore, effects of other fuel properties such as distillation on exhaust emissions were investigated. The results show that sulfur is the influential factor for both devices. Namely, high NOx emission reduction performance of the Urea-SCR system with the oxidation catalyst at low exhaust gas temperature operation is influenced by sulfur.

Clarifying the impact of ETBE 8% blended fuel on current Japanese gasoline vehicles, under the Japan Clean Air Program II (JCAPII) we conducted exhaust emission tests, evaporative emission tests, durability tests on the exhaust after-treatment system, cold starting tests, and material immersion tests. ETBE 17% blended fuel was also investigated as a reference. The regulated exhaust emissions (CO, HC, and NOx) didn't increase with any increase of ETBE content in the fuel. In durability tests, no noticeable increase of exhaust emission after 40,000km was observed. In evaporative emissions tests, HSL (Hot Soak Loss) and DBL (Diurnal Breathing Loss) didn't increase. In cold starting tests, duration of cranking using ETBE 8% fuel was similar to that of ETBE 0%. In the material immersion tests, no influence of ETBE on these material properties was observed.

Emission regulations for diesel-powered vehicles have been gradually tightening. Installation of after-treatment devices such as diesel particulate filters (DPF), NOx storage reduction (NSR) catalysts, and so on is indispensable to satisfy rigorous limits of particulate matter (PM) and nitrogen oxides (NOx). Japan Clean Air Program II Oil Working Group (JCAPII Oil WG) has been investigating the effect of engine oil on advanced diesel after-treatment devices. First of all, we researched the impact of oil-derived ash on continuous regeneration-type diesel particulate filter (CR-DPF), and already reported that the less sulfated ash in oil gave rise to lower pressure drop across CR-DPF [1]. In this paper, impact of oil-derived sulfur and phosphorus on NSR catalyst was investigated using a 4L direct injection common-rail diesel engine with turbo-intercooler. This engine equipped with NSR catalyst meets the Japanese new short-term emission regulations.

Numerous studies of pelvic tolerance to lateral impact aimed at protecting car occupants have been conducted on Post Mortem Human Subjects (PMHSs) in a sitting posture. However, it remains unclear whether or not the results of these studies are relevant when evaluating the injury risk to walking pedestrians impacted by a car. Therefore, the first objective of the present study is to determine the injury tolerance and to describe the injury mechanisms of the human pelvis in lateral impacts simulating car-pedestrian accidents. The second objective is to obtain data for validation of mathematical models of the pelvis. In-vitro experiments were conducted on twelve PMHSs in simulated standing position. The trochanter of each PMHS was hit by a ram at speed of 32 km/h, and the pelvic motion was constrained by a bolt. This type of pelvic constraint is difficult to simulate in mathematical models.

Intermittent Dual-fluid Exhaust Burner (IDEB) has been developed to reduce emissions from methanol fueled vehicles during the warm-up period after a cold start. The IDEB does not need any special fuel injector or blower, and has been built mainly through software modification of an ECU. An FTP mode test while operating an IDEB confirmed that the catalyst temperature was rapidly increased to significantly reduce the emissions to meet a level of ULEV standards.

For the better understanding of nanoparticles observed on the rode side, adding to the emission test on the chassis dynamometer and engine dynamometer test, possible factors for formation of nanoparticles are investigated. As other possible factors, cold starting of transient test cycle, blow-by gas from heavy duty diesel engine without a positive crankcase ventilation, exhaust braking, and plume mixing of vehicle exhausts were investigated. Nuclei mode particles under the transient test cycles formed during fuel cut period, fuel enrichment period and idling period. Concentration of nuclei mode particles during the idling period are depends on exhaust temperature. The higher exhaust temperature courses the lower number concentration but variation range is within twice. Emission rate of nanoparticles from blow-by gas is one thousandth of tail pipe emissions rate and was found to be negligible.

Ultra-low energy consumption and ultra-low emission vehicle technologies have been developed by combining petroleum-alternative clean energy with a hybrid electric vehicle (HEV) system. Their component technologies cover a wide range of vehicle types, such as passenger cars, delivery trucks, and city buses, adsorbed natural gas (ANG), compressed natural gas (CNG), and dimethyl ether (DME) as fuels, series (S-HEV) and series/parallel (SP-HEV) for hybrid types, and as energy storage systems (ESSs), flywheel batteries (FWBs), capacitors, and lithium-ion (Li-ion) batteries. Evaluation tests confirmed that the energy consumption of the developed vehicles is 1/2 of that of conventional diesel vehicles, and the exhaust emission levels are comparable to Japan's ultra-low emission vehicle (J-ULEV) level.

Instantaneous temperature of in-cylinder gas provides a lot of useful and local information for analyzing the combustion process in an internal combustion engine. From the standpoint of applicability to a practical engine, the infrared monochromatic radiation pyrometry required only a single optical window is considered to be more suitable comparing with the conventional infrared absorption-emission pyrometry with two optical windows. Then, the former pyrometer is used to measure the mean gas temperatures averaged on an optical path (or cylinder diameter) of a spark ignition engine connected to a prechamber with a torch nozzle of various area sizes. These measured temperature-crankangle diagrams not only clarify the influences of torch jet flow on the combustion processes, but also correspond well to the heat release rates calculated from the pressure diagrams.

In order to investigate the possibility of noise countermeasures taken on the road and in its surroundings an urban area exposed to high road traffic noise level was taken up as a model, and their effectiveness was estimated by a hybrid simulation method combining a scale model experiment technique and a computer simulation. The case studies of simulation were carried out in the case of improving the road structures, laying the noise barriers, constructing the noise-buffer buildings and so on. As a result, more than 20 dB (A) of road traffic noise reduction were obtained by a modification of the existing surface road to an elevated road.

The objective of this study is to improve tire hydroplaning performance by examining the arrangement of the tread grooves, based on water flow. It is important to smoothly channel the water through the tread grooves to improve performance. For this purpose, flow around the tire contact area was visualized by particle tracing. The velocity and the direction of flow in front of the contact area became clear as a vector map. This vector map indicated that the direction of the flow depends primarily on the lateral position, i.e., the distance from the tread center. Tread grooves parallel to the flow vector were designed based on this result. The visualization of the improved tire demonstrated that water flowed smoothly along the grooves. In addition, a drum test indicated increased cornering force at high speed.

The non-physiological motions of human cervical vertebrae were analyzed in volunteer tests for rear-end impacts and were considered to be an important parameter for neck injuries. The objectives of this study are to improve the Marko de Jager neck model using volunteer test data and to analyze the influence of horizontal and vertical accelerations on cervical vertebral motion. In the beginning of this study, a neck model was positioned based on X-ray cineradiography of a volunteer. Motions of each vertebra were compared with those of volunteer test data for low speed rear-end impacts (4, 6, 8km/h). In these comparisons, the differences of vertebrae motions between the neck model and the volunteer tests were found. To improve the validity of the neck model, the connection properties and the bending properties of the upper and lower vertebrae of the model were modified to increase rigidity.

In recent research, decreasing oil consumption and using a synthetic oil have been shown to be effective methods of reducing smoke emissions. However, the investigation of the constituents of white smoke and its environmental effect on humans have not been undertaken. The purpose of this investigation is to clarify the characteristics and compositions of white smoke and to analyze its environmental effect on humans using Ames test, and to evaluate a control for reduction of emitted matter by steady-state engine tests. Emitted matters(EM) from synthetic oil is less than that of semi-synthetic and mineral oils under the same test conditions. Emission after treatment resulted in the lowest EM when simulating the results of the ISO 6460 test, which results showed a decrease to about 1/10. EM from two-stroke engine mainly consists of unburned engine-oil and more than 95 % of EM is soluble organic fraction (SOF).

In order to establish a systematic approach to the study on the injuries sustained by motorcycle riders in accidents and the assessment of protective devices fitted to motorcycles, this research develops a computer simulation model of motorcycle-to-vehicle collision model based on multibody kinematics and dynamics using MADYMO (MAthematical DYnamic MOdel). The effectiveness of the motorcycle-to-vehicle crash model is verified using data of 14 full-scale tests. Comparisons between the simulation peak head acceleration results and the full-scale crash tests data demonstrate a satisfactory agreement between them. The simulation results along with the test data indicate that the leg protectors fitted to the motorcycle can induce harmful consequences to the rider head in some configurations, regardless of their aimed protective effects on the rider’s legs. The findings obtained in this study also provide basis for further improvement of the current model.